Why thick oil needs a bigger feed hole
A disposable device feeds liquid by capillary action: the oil is drawn up by the wicking cotton and delivered to the heater. The higher the viscosity, the slower the flow.
Standard 50/50 PG/VG runs at roughly 50–200 cP. Thick oil at VG 70–80% can reach 800–3000 cP - an order of magnitude higher. If the hole is undersized, the feed rate cannot keep up with the rate of vaporization. The heater runs dry locally: you get a burnt or dry hit, vapor output drops off in the second half of the device, and in severe cases the ceramic cracks or the cotton scorches.
The direction is therefore clear: for thick oil, what you enlarge is the feed channel, not the power.
Sizing by viscosity

Viscosity figures are reference ranges at 25°C; use your own measured values. Hole diameters are starting points, not fixed specifications.
Why you cannot simply keep enlarging the hole
Two physical limits cap the hole size.
Temperature. Going from 25°C to 40–45°C drops VG viscosity by more than one grade. Once the hole exceeds about 2.0 mm, hot conditions flood the atomizing chamber faster than the heater can vaporize, and the excess escapes through the air path or the connector - the classic summer leakage complaint.
Pressure. Air transport, high altitude, courier transit, cap opening, or sustained draws all create pressure differentials that push liquid through an oversized hole. The result is flooding on unboxing or spit-back on the first puff.
Hole sizing is a balance: small enough to prevent leakage, large enough to keep feeding.
The better answer: distributed holes, not one oversized hole
With the same total feed area, four small holes outperform one large hole:
lower localized negative pressure at each hole, so liquid is not drawn through too fast;
if one point does leak, the loss is a quarter of a single-hole design;
more even saturation across the wick, so the area near the hole does not run dry first.
This is why 4×1.8 mm has become the mainstream configuration for thick-oil products rather than a single 2.5 mm hole.
Hole size is not a standalone parameter
Enlarging the hole alone rarely fixes a dry hit. Three other elements must move with it:
Wicking cotton - loose, low-gsm, highly oleophilic; never over-compressed. A compressed wick can feed at half the rate of a loose one, effectively shrinking the hole again.
Heater - high-porosity sintered ceramic (45% or above) is preferred. Cotton coils tend to scorch or burn through under thick oil.
Draw resistance and power - a tighter MTL draw uses negative pressure to assist wicking; keep power moderate at 1.2–1.4 Ω and 10–14 W. A preheat function makes a clear difference on the first puff and in cold conditions.
Two details that are often missed: let the device stand at least 30 minutes after filling before assembly (60 minutes for thick oil), otherwise a dry first puff gets blamed on the hardware; and use lead-free stainless steel (SS316 or equivalent) for the center post with a PCTG tank, both of which directly affect heavy-metal compliance in destination markets.
A note for high-temperature markets
For markets with summer temperatures above 40°C - the Middle East, parts of Southeast Asia - keep the hole at 1.7–1.8 mm and stop there. Put the effort into leakage control instead: dual-layer cotton, a separate air chamber, sealing silicone. In hot conditions, enlarging the hole raises leakage far more than it improves feeding.
For cold markets below 0°C, viscosity rises significantly: 2.0–2.4 mm is acceptable, with preheat made mandatory.
How to validate during sampling
A parameter table only gives direction; the final decision must come from testing. Run at least these five:
10 consecutive puffs at room temperature - check for dry hits and vapor decay;
30 minutes at 5°C, then puff - low-temperature feeding;
24 hours at 40–45°C, upright and inverted - high-temperature leakage;
puff at roughly 20% remaining oil - end-of-life feeding, the test that most often exposes an undersized hole;
simulated transport vibration or 1 m six-face drop, then inspect.
End-of-life feeding and inverted high-temperature leakage are the two veto items. Fail either one and the configuration cannot be approved for thick oil.
Three common mistakes
Bigger hole equals better feeding. It ignores viscosity drop at high temperature and pressure variation, and buys leakage complaints instead.
Raising power to fix a dry hit. Higher power drains the wick faster and makes starvation worse; fix the feed channel instead.
Copying someone else's hole size. Formulation, wick gsm and ceramic porosity differ, so the same hole behaves differently. Test against your own materials.
FAQ
Does thick oil always require 4 holes? No. Two holes at 2.0 mm can reach a similar total feed area, but distribution and leak resistance are worse and consistency is harder to control in mass production.
Is 2.0 mm the upper limit? For most disposable designs, yes. Above 2.0 mm you need stricter leakage control, and it is not recommended for hot climates.
Will a larger hole alone solve dry hits? No. Hole size, wick, ceramic porosity and draw resistance work as a set; changing one usually yields partial improvement only.
How do I judge whether a supplier's configuration is reliable? Ask for hole diameter, hole count, ceramic porosity and the supported viscosity range in writing, plus 40°C/24h leakage and end-of-life feeding data. A supplier who cannot give specific numbers generally lacks thick-oil capability.
Can one hardware platform serve all markets? Not advisable. Viscosity behaviour differs clearly between hot and cold markets; manage separate versions, or add preheat and reinforced sealing on the same platform.
If you are specifying hardware for a thick-oil product, send us your e-liquid parameters and target market-we will propose a hole configuration matched to your viscosity range and share the sampling test records.
